循环吸湿对炭纤维复合材料界面性能的影响

通过对炭纤维增强复合材料进行70、85、100℃下的循环水浸吸湿试验,研究了复合材料在不同水浸温度下的吸湿-脱湿行为规律。同时,对循环吸湿-脱湿过程中的试样进行层间剪切强度测试和动态力学性能测试,并结合扫描电镜观察循环吸湿各个阶段的纤维基体结合状态。结果表明,水浸温度越高,水分的扩散速率越快,饱和吸湿率越大。经过循环吸湿后复合材料的吸湿行为仍满足Fick第二定律,吸湿后层间剪切强度下降,湿热循环次数越多下降的越明显。脱湿后层间剪切强度有所恢复,水浸温度越高造成的不可逆破坏越大,层间剪切强度恢复的越少。干态时的玻璃化转变温度为231℃,吸湿后下降了37℃。     

纺丝工艺对炭纤维缠绕复合材料强度转化率的影响

通过不同纺丝工艺的聚丙烯腈基炭纤维表面状态、NOL环及Φ150 mm容器的实验研究,分析了不同纺丝工艺对湿法缠绕复合材料聚丙烯腈基炭纤维强度转化率的影响。结果表明,干喷湿纺炭纤维比湿法纺丝Φ150 mm容器环向纤维强度转化率要高出11.9%~15.4%,湿法纺丝的炭纤维复合材料NOL环层间剪切强度要比干喷湿纺炭纤维复合材料高7.4~34.1 MPa。因此,干喷湿纺的炭纤维可应用于固体火箭发动机缠绕壳体、压力容器等主要承受拉伸应力的领域,可充分发挥其纤维强度;而湿法纺丝工艺制成的炭纤维与树脂基体结合紧密,利于载荷的传递,可应用于承受压缩剪切等复杂载荷的领域,从而发挥这两种纤维各自不同优势。     

Tear Resistance of Orthogonal Kevlar-PWF-reinforced TPU Film

This work seeks to investigate the notch sensitivity and fracture behaviour of orthogonal Kevlar-plain woven fabric (PWF)-reinforced thermoplastic polyurethanes (TPU) film applied to high altitude balloon. Four types of specimens are implemented to measure notched strength and fracture toughness by conducting static tension and tear tests on an MTS system respectively. The damage and failure mechanisms are discussed and the results for notched strength and tear resistance are evaluated and compared with each other. From the experiments, it is found that the notch sensitivity of the film increases with the increase in the size of the hole, but the notch sensitivity and the stress concentration of the notch are insignificant and there is a decrease of only about 4%-10% in tensile strength for the notched specimens with different hole sizes in diameter compared with the unnotched specimen. In contrast, the tear resistance containing a central slit with only 1 mm length is about half of tensile strength of the unnotched film, which implies that the tear resistance exists an significant notch sensitivity. The results of this study provide an insight into notch sensitivity and fracture behaviour of the Kevlar-PWF-reinforced TPU film and constitute a fundamental basis for the design of high altitude balloon.     

基于精益6滓的航空高强钢零件大尺寸面轮廓度 数控加工参数优化

针对某航空高强钢零件大尺寸面轮廓度数控加工合格率较低问题,利用精益6σ方法,依据DMAIC的研究路径,充分运用箱线图、等方差检验、单因子方差分析等方法和工具,分析了“人、机、料、法、环、测”6大方面的操作者、加工刀具、装夹方式、主轴转速、切削量、进给速度、切削方式7个因素,确定刀具尺寸、切削量、进给速度为关键影响因素;通过建立面轮廓度与7个影响因素之间的GLM模型,得出影响流程输出的3个关键影响因素的最佳组合,并在此基础上对工艺参数进行优化。结果表明:该零件的数控加工工艺流程改进后,减少了加工过程中的人工调试检查环节,缩短了加工调试验证时间,大尺寸面轮廓度数控加工合格率从80%提高到96%以上,取得了较好的经济效益。     

Effects of sintering temperature and time on defect evolution and compression properties of Ti-Al3Ti laminated composites

For metal-intermetallic laminated composites, various types of defects often occur during the preparation process. This paper studied the evolution and formation mechanism of defects,such as pores, tunnel cracks, and delamination cracks in Ti-Al₃Ti laminated composites prepared by vacuum hot-pressing method. Moreover, quasi-static and dynamic compression tests were performed to study the effects of pores and delamination cracks on the compression properties of the composites. The resu...     

纤维增强树脂基复合材料结构的优化设计

综述了国内外纤维增强树脂基复合材料结构优化设计的研究成果与发展状况，内容涉及到层合板壳结构以及夹层结构的屈曲、振动、可靠性、结构强度以及多级多目标等问题的优化设计。文中还涉及到发动机复合材料构件优化方面的一些研究成果，给出了其优化设计的网络框图。论文最后对复合材料结构优化设计当前存在的主要问题和今后发展方向作了分析，并指出今后的研究方向：（１）多级多目标多学科的优化设计，不仅涉及到基本理论、建模和方法，而且更加强调工程实际问题；（２）发展相应的软件专家系统，更加强调软件面向对象编程和 Ｃ Ａ Ｄ 技术的应用；（３）注重探究快速有效的优化算法以及探究随机优化和可靠性优化技术，从而快速有效地获得对优化设计点的可靠评价等。     

结构比强度及其在优化设计中的应用

本文从结构重量角度推导了比强度(含比模量)表达式,分析了对同一材料不同比强度的关系,给出了比强度在结构动态分析中及结构优化设计中的应用。     

二维三轴编织复合材料压缩失效行为的细观有限元模拟

为研究典型二维三轴编织复合材料（2DTBC）的压缩破坏机理，建立了细观有限元模拟方法体系。提出了反映编织复合材料真实几何特性的单胞模型建模策略，根据Murakami-Ohno损伤理论建立了各向异性损伤模型来模拟纤维束中的损伤起始和扩展行为，通过引入波动系数描述了纤维束的起伏状态，并采用内聚力单元来模拟界面分层。在此基础上，分析得到了二维三轴编织复合材料在压缩载荷下的破坏过程，研究了压缩载荷下纤维束和界面层的损伤演化，探讨了纤维束波动对压缩性能的影响规律。通过与相关试验结果对比，该模型能够准确预测二维三轴编织复合材料在面内压缩载荷下的力学响应和主要失效行为，以及自由边效应。细观失效过程分析结果表明，二维三轴编织复合材料轴向压缩的破坏是由轴向纤维束的纤维压缩失效主导的；横向压缩破坏则是由偏轴纤维束的纤维压缩失效引起的。     

斜激波极值规律的边界层影响

采用边界层理论与斜激波/膨胀波精确算法，建立一种结合Eckert参考温度法和Illingworth-Stewartson变换法优势的边界层权重算法，用于研究超声速黏性楔面边界层位移厚度对斜激波极值规律的影响。分别应用层流Navier-Stokes方程和湍流Navier-Stokes方程的CFD解算器对边界层新模型进行了算例精度评估。在来流马赫数为1.2~2.4和楔面角为3°~20°的范围内，压强比的相对误差小于0.1%。计入层流与湍流边界层影响的理论模型研究表明，边界层影响使得最优马赫数增加；对于层流边界层，最优马赫数增量约为0.001 5~0.003 3；对于湍流边界层，最优马赫数增量约为0.002 8~0.006 1。     

Grinding performance evaluation of porous composite-bonded CBN wheels for Inconel 718

For high-efficiency grinding of difficult-to-cut materials such as titanium and nickel alloys, a high porosity is expected and also a sufficient mechanical strength to satisfy the function.However, the porosity increase is a disadvantage to the mechanical strength. As a promising pore forming agent, alumina bubbles are firstly induced into the abrasive layer to fabricate porous cubic boron nitride（CBN） wheels. When the wheel porosity reaches 45%, the bending strength is still high up to 50 MPa with modified orderly pore distribution. A porous CBN wheel was fabricated with a total porosity around 30%. The grinding performance of the porous composite-bonded CBN wheel was evaluated in terms of specific force, specific grinding energy, and grinding temperature, which were better than those of the vitrified one under the same grinding conditions. Compared to the vitrified CBN wheel, clear straight cutting grooves and less chip adhesion are observed on the ground surface and there is also no extensive loading on the wheel surface after grinding.